LUVTruck.com

phpBBV3 Message Board
It is currently Fri Jul 18, 2025 12:08 am

View unanswered posts | View active topics


Board index » Technical » Stock Trucks

All times are UTC - 6 hours




Post new topic Reply to topic  Page 1 of 1
  [ 8 posts ] 
  Previous topic | Next topic 
Author Message
Callmelazy
PostPosted: Sat Apr 14, 2012 6:13 pm 
Offline
Member

Joined: Sat Nov 26, 2011 11:11 pm
Posts: 28
Was cleaning my egr valve out with a little drill. Wanted to get it good. So went a bit bigger. And bored the port too much. Am I doomed? Did I screw the pooch ?
Top
 Profile  
Reply with quote  
jeffklam
PostPosted: Sat Apr 21, 2012 4:59 pm 
Offline
lives at LUVTruck.com
User avatar

Joined: Wed Nov 16, 2005 3:02 pm
Posts: 297
Location: White Bear Lake, MN
Post a picture.

_________________
1978 LUV Custom - 1979 LUV stock
Top
 Profile  
Reply with quote  
Callmelazy
PostPosted: Sun Apr 22, 2012 12:48 am 
Offline
Member

Joined: Sat Nov 26, 2011 11:11 pm
Posts: 28
Here it is.


Attachments:
2012-04-21 23.40.18.jpg
2012-04-21 23.40.18.jpg [ 99.96 KiB | Viewed 2291 times ]
Top
 Profile  
Reply with quote  
dkay
PostPosted: Sun Apr 22, 2012 9:20 am 
Offline
lives at LUVTruck.com
User avatar

Joined: Sun Feb 23, 2003 9:46 pm
Posts: 254
Location: Hillsboro, OR
Make a new restricted orifice out of some rod material and insert it into the hose.

-DK
Top
 Profile  
Reply with quote  
egg
PostPosted: Sun Apr 22, 2012 10:05 am 
Offline
LUVTruck.com Lifer

Joined: Sun May 15, 2005 4:57 pm
Posts: 680
Location: Cornelius Ore
If that is where the vacuum line attaches to the unit no problem. If it is an exhaust flow port then the size is important.
Top
 Profile  
Reply with quote  
Callmelazy
PostPosted: Mon Apr 23, 2012 8:10 pm 
Offline
Member

Joined: Sat Nov 26, 2011 11:11 pm
Posts: 28
Its where the vaccum hose is. Any good rod material I should use ? Or type of adaption ?
Top
 Profile  
Reply with quote  
cleaver
PostPosted: Tue Apr 24, 2012 7:59 am 
Offline
da LUV masta

Joined: Wed Jun 09, 2010 12:22 pm
Posts: 550
Location: Redfield SD
Sleeve some copper pipe into it.
Top
 Profile  
Reply with quote  
egg
PostPosted: Tue Apr 24, 2012 12:06 pm 
Offline
LUVTruck.com Lifer

Joined: Sun May 15, 2005 4:57 pm
Posts: 680
Location: Cornelius Ore
If you know what the original size was just fill it with epoxy amd drill a new hole. As I said before if it is a vacuum line connection only, you don't have a problem anyway. Vacuum is sent there to open the valve under certain conditions. The exhaust flow amount is determined by a port inside the valve itself.
Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 8 posts ] 

Board index » Technical » Stock Trucks

All times are UTC - 6 hours


Who is online

Users browsing this forum: Bing [Bot] and 12 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group