LUVTruck.com

phpBBV3 Message Board
It is currently Sat Jun 21, 2025 3:22 am

View unanswered posts | View active topics


Board index » Technical » Stock Trucks

All times are UTC - 6 hours




Post new topic Reply to topic  Page 1 of 1
  [ 13 posts ] 
  Previous topic | Next topic 
Author Message
budbondo
 Post subject: fixing the trans
PostPosted: Sat Dec 29, 2007 3:54 am 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
ok i got the stuff to fix the trans i got the hole clutch kit with pilot,presher plate any thing you all can say to help all info good or bad ok i was going to also put the 5-speed in at the same time but it is the one that has the remote on it and i need to kut the floor about 6" back and move the fuel lines i will see when i get the trans out i got the whole kit for 105.00 dam good deal

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
ugotluv
 Post subject:
PostPosted: Sat Dec 29, 2007 11:42 am 
Offline
LUVTruck.com Lifer
User avatar

Joined: Sat Jul 14, 2007 9:00 pm
Posts: 641
Location: devils lake north dakota
thats a real good deal :D
Top
 Profile  
Reply with quote  
budbondo
 Post subject:
PostPosted: Sun Dec 30, 2007 10:08 pm 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
got the trans out and again i did not need to pull the motor with it i am going to put the clutch kit in tomorrow and drive it and then this summer i am going to put the 5speed and disc rearend in after i save up sum $$$ for sum parts that i need to complete the job right :lol:

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
OzLuvTrucker
 Post subject:
PostPosted: Sun Dec 30, 2007 11:03 pm 
Offline
Australian LUV Guru
User avatar

Joined: Thu Apr 19, 2007 5:08 am
Posts: 782
Location: Australia
Image The remote gearstick unbolts and the stock luv stick bolts in, no need to cut the floor.

_________________
1980 4x4 KBD40 ISUZU/Chev Luv
Factory Fitted c190 Diesel Engine, ARB BullBar, Ramsey Winch, Custom Tilt Tray,
Image
LUVTRKR wrote:
It does have a license plate so technically it is a street truck, that sets off car alarms and makes kids cry. lol
Top
 Profile  
Reply with quote  
budbondo
 Post subject:
PostPosted: Mon Dec 31, 2007 8:51 pm 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
i got the tool to pull the pilot bearing out and that sun of a snitch will not come out i put wd-40 and i am going to let it sit over night and try tomorrow and now i need a flywheel mine as sum cracks in it and i got the trans out so i will do it right this time ok laters to all and happy new years :microwave: :drinking: :popcorn: :smt021 :smt020 :smt028 :smt043 :smt050 :smt068 :smt067 :smt066 :smt064

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
mytmouz
 Post subject:
PostPosted: Tue Jan 01, 2008 1:41 am 
Offline
Addicted to LUV

Joined: Mon Aug 28, 2006 11:54 pm
Posts: 6584
Location: Pelahatchie, MS
Never pulled the pilot in a LUV, but on others I've packed the pilot hole full of grease and used an appropriate sized wooden dowel or piece of round stock to just slip in the pilot hole and forced the bearing out by using a shop hammer and tapping on the dowel.

_________________
If you think no one cares, try missing a couple of payments...



FIAA!

SFPP!
Top
 Profile  
Reply with quote  
budbondo
 Post subject:
PostPosted: Tue Jan 01, 2008 3:25 am 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
i did that lol and the little ring popped of and the grease came out :( it was funny so i went and got the tool and it is just rusted :x :? in there but i will win in the end lol i am getting a new fly wheel for $60.00 so that is a good deal $170.00 total for a new clutch set up i luv it and next is the rearend

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
rondog
 Post subject:
PostPosted: Tue Jan 01, 2008 9:49 am 
Offline
Addicted to LUV

Joined: Sun Jun 06, 2004 11:48 pm
Posts: 6365
Location: Whittier, (So). Cal.
I cut one out with a small air hammer once.

_________________
OK, I'm over it. Where's the beer? 8)
Top
 Profile  
Reply with quote  
budbondo
 Post subject:
PostPosted: Tue Jan 01, 2008 3:22 pm 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
yep thats my next option i am going to get to it in a bit i will let you all know :lol:

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
budbondo
 Post subject: fly wheel bolts specs
PostPosted: Wed Jan 02, 2008 7:30 pm 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
well i got it out it had to be cut and i also used a dremel it had gotten hot and welded it self but i got the new one in and my new fly wheel will be in tomorrow after noon and on the 5 speed the shifter plates are not the same so i will still need to cut a hole but no big deal i have been cutting up trucks and cars for years and any one know what the torc specs are on the fly wheel bolts the 6 that hold the fly wheel on lol :wink:

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
budbondo
 Post subject:
PostPosted: Thu Jan 03, 2008 3:31 pm 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
i need the torc specs for the fly wheel any one got them thanks for all your help guys i will be driving my luv hopefully by the weekend after 8 months 8) :P then i need to but new brakes on the rearend

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
budbondo
 Post subject:
PostPosted: Fri Jan 04, 2008 5:26 pm 
Offline
Addicted to LUV
User avatar

Joined: Sat Feb 04, 2006 12:17 am
Posts: 1075
Location: porterville,cali
i got it done she runs good and quiet

_________________
http://www.facebook.com/ez.cracker
dangerous-toys4life
73 3-door avalanche bdydropped on 18s
86 1-ton 4x crewcab short bd 15"lift
75 k-5 2x
94 king cab
Image
Top
 Profile  
Reply with quote  
egg
 Post subject:
PostPosted: Fri Jan 04, 2008 7:38 pm 
Offline
LUVTruck.com Lifer

Joined: Sun May 15, 2005 4:57 pm
Posts: 680
Location: Cornelius Ore
Probably too late but torque specs for flywheel are 69 ft lbs.
Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 13 posts ] 

Board index » Technical » Stock Trucks

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 3 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group