LUVTruck.com

phpBBV3 Message Board
It is currently Thu Mar 28, 2024 3:26 pm

All times are UTC - 6 hours




Post new topic Reply to topic  [ 16 posts ] 
Author Message
PostPosted: Fri Dec 20, 2013 6:55 pm 
Offline
Junior Member

Joined: Wed Aug 22, 2012 7:38 pm
Posts: 11
I have a 74' luv that had front disc brakes and rear drums when I purchased. I just installed a Ford 9" rear end. The package installed included a bolt on disc brake kit. Calipers are installed correctly (bleed screw up) and the system has been power bled; however, I am still having braking issues. The pedal is currently 4:1 and there is a small booster in the system.

I was going to leave the booster, but there is not enough room to upgrade it and the master cylinder. So, we were told to remove the small booster and just go manual. To do this, I was told that I need a new master cylinder (dual chamber), but that it needs a 7/8 bore on both sides to bring the front brakes up to the stopping power of the rear brakes and then I need to add a proportioning valve to help balance it all out. Further, I was told that the pedal will need to be brought to 7:1. This of course is not going to be as cost effective as I had hoped.

Does anyone have any other master cylinder (with or without booster) suggestions for a 74 luv w/V-8 swap, 9 in Ford rear end and 4 wheel discs all around (front and rear discs are different? I am not a brake guy and truly do not know where to start.


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 7:09 pm 
Offline
Addicted to LUV

Joined: Mon Aug 28, 2006 11:54 pm
Posts: 6584
Location: Pelahatchie, MS
I am running one for a Chrysler mini van. Same as what strange sells

. No booster and a 5:1 pedal ratio. (7:1 doesn't sound right). I have wilwood fronts now, but ran the same setup with the stock fronts. I have the Lincoln Versailles factory nine inch rear discs...

_________________
If you think no one cares, try missing a couple of payments...



FIAA!

SFPP!


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 8:39 pm 
Offline
Addicted to LUV

Joined: Fri Jul 01, 2005 9:41 pm
Posts: 6289
Location: Camarillo, CA
Ben had stock front brakes and rear discs on a nine inch. He ran the stock master and booster and it was fine. The pick shows a line lock for the front end.

Image

_________________
Certified pilots, looking down on people since 1903.


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 9:49 pm 
Offline
Junior Member

Joined: Wed Aug 22, 2012 7:38 pm
Posts: 11
Our set up is currently the same as "Luvrv8", but we noticed that there is some type of possible proportioning valve installed on the fender well. It doesn't look as if it is adjustable. We have bled the system a couple of times and still have no pedal unless pumped 5 or 6 times. Do you think this valve should be removed or could it be a bad master cylinder? I looked at the reconditioned masters online and they say they are 7/8 in. bore, so I am unsure as to why I would need to run a different master. We measured the pedal and the brake guy who told us we needed to upgrade the master said the pedal was 4:1. Do you think a 4:1 pedal would be appropriate? Also, any thoughts on a residual valve for the rear? Any suggestions would be really helpful.

Image


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 10:36 pm 
Offline
Addicted to LUV

Joined: Fri Jul 01, 2005 9:41 pm
Posts: 6289
Location: Camarillo, CA
That is called a fail indicator.

_________________
Certified pilots, looking down on people since 1903.


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 11:01 pm 
Offline
Junior Member

Joined: Wed Aug 22, 2012 7:38 pm
Posts: 11
Does the fail indicator have a proportioning valve built in? I cannot find anything on it online. Does it need to be removed?


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 11:14 pm 
Offline
Addicted to LUV

Joined: Mon Aug 28, 2006 11:54 pm
Posts: 6584
Location: Pelahatchie, MS
I removed mine when I plumbed it...

_________________
If you think no one cares, try missing a couple of payments...



FIAA!

SFPP!


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 11:16 pm 
Offline
Addicted to LUV

Joined: Fri Jul 01, 2005 9:41 pm
Posts: 6289
Location: Camarillo, CA
It's really not needed, it just kicks a light if the pressure from back to front gets too far out of pressure differential.

_________________
Certified pilots, looking down on people since 1903.


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 11:20 pm 
Offline
Junior Member

Joined: Wed Aug 22, 2012 7:38 pm
Posts: 11
Do you think it could be causing a braking issue?


Top
 Profile  
Reply with quote  
PostPosted: Fri Dec 20, 2013 11:24 pm 
Offline
Addicted to LUV

Joined: Fri Jul 01, 2005 9:41 pm
Posts: 6289
Location: Camarillo, CA
Never say never but I doubt it. It does not take much to remove, just remove it.

_________________
Certified pilots, looking down on people since 1903.


Top
 Profile  
Reply with quote  
PostPosted: Sat Dec 21, 2013 5:39 am 
Offline
Addicted to LUV
User avatar

Joined: Sun Jan 22, 2006 1:11 am
Posts: 2803
Location: Baytown,Texas
Here are some links to the info i used . I also Have 7 to 1 with manual cylinder .
https://www.mpbrakes.com/techtalk/how-t ... edal-ratio
http://www.markwilliams.com/braketech.aspx
http://www.mcleodracing.com/info/?id=5262


Top
 Profile  
Reply with quote  
PostPosted: Sat Dec 21, 2013 8:51 am 
Offline
Addicted to LUV

Joined: Mon Aug 28, 2006 11:54 pm
Posts: 6584
Location: Pelahatchie, MS
7:1 it is then, if Hotrod says so...

_________________
If you think no one cares, try missing a couple of payments...



FIAA!

SFPP!


Top
 Profile  
Reply with quote  
PostPosted: Sat Dec 21, 2013 1:30 pm 
Offline
Addicted to LUV
User avatar

Joined: Sun Jan 22, 2006 1:11 am
Posts: 2803
Location: Baytown,Texas
I had to go like 7.7 on mine . I have aerospace brakes on mine . If your not an old man like me 5 to 1 will work good .


Top
 Profile  
Reply with quote  
PostPosted: Sat Dec 21, 2013 4:09 pm 
Offline
Assimilated into LUVTruck.com

Joined: Tue Oct 07, 2008 8:07 pm
Posts: 906
Location: N W Arkansas
There is an adjustable rod from the stock booster that must be set at the correct length for the master to work properly. If you retain the stock setup make sure you check this.

_________________
'78 Chevy LUV,1.9,4sp,headers,31's,SAS Dana 30,Dana 20,SOA rear w/Aussie Locker, rough body, bought new 12/4/78.
'87 Trooper,2.3,5sp,headers,31's,ball joint flip & spacer,Aussie Locker rear,Superwinch hubs,brush guard w/5.5K winch,more to come.


Top
 Profile  
Reply with quote  
PostPosted: Mon Dec 23, 2013 3:53 am 
Offline
Addicted to LUV
User avatar

Joined: Sat May 11, 2002 3:47 pm
Posts: 3467
Location: Sand Bernardino, CA
I've had 3 different brake setups on the back of a LUV (1 drum, 2 disc) and none of them had this problem. I think something else is wrong.

For example, one time I saw a set of rear calipers that weren't sliding on the pins. Same symptoms you described. We noticed that when you pumped the brakes a few times, that rotor would bend as the caliper clamped down. Then, when you let off, the rotor would push the piston back into the caliper, so next time you had to pump again.


Top
 Profile  
Reply with quote  
PostPosted: Mon Dec 23, 2013 11:08 am 
Offline
Addicted to LUV
User avatar

Joined: Sun Jan 22, 2006 1:11 am
Posts: 2803
Location: Baytown,Texas
I also had the factory set up with a 9inch ford and ford drums . It workrd great


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ] 

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 15 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group