LUVTruck.com

phpBBV3 Message Board
It is currently Fri Jun 20, 2025 3:12 pm

View unanswered posts | View active topics


Board index » Technical » General Automotive

All times are UTC - 6 hours




Post new topic Reply to topic  Page 1 of 1
  [ 6 posts ] 
  Previous topic | Next topic 
Author Message
luvondope
 Post subject: glue removal
PostPosted: Sat Dec 01, 2007 9:20 pm 
Offline
da LUV masta
User avatar

Joined: Sat Aug 03, 2002 6:53 pm
Posts: 502
Location: Baytown ,Tx
What get the glue off used to hold the side moldings on? Like the molding that goes down the side 80 model chevys?
Top
 Profile  
Reply with quote  
rondog
 Post subject:
PostPosted: Sat Dec 01, 2007 9:34 pm 
Offline
Addicted to LUV

Joined: Sun Jun 06, 2004 11:48 pm
Posts: 6365
Location: Whittier, (So). Cal.
Try rubbing alcohol on a rag. Or try some Goof off, Go Gone ,or Dissolve-it.
Then maybe acetone or laquer thinner. But very careful with these two. They can hurt the paint.

Also try Diesel fuel, or that spray can brake cleaner. But brake cleaner can also hurt the paint.

And what ever you use, if the paint is in good shape, I would give it a good wax job afterwards.

_________________
OK, I'm over it. Where's the beer? 8)
Top
 Profile  
Reply with quote  
tumwatertaz
 Post subject:
PostPosted: Sat Dec 01, 2007 10:11 pm 
Offline
PITA Old Fart

Joined: Thu May 22, 2003 8:33 am
Posts: 2286
Sometime WD40 will soften it up enough so that you can CAREFULLY remove it by scraping it off with a razor blade.

Good Luck.
Top
 Profile  
Reply with quote  
luvondope
 Post subject: Thanks
PostPosted: Sat Dec 01, 2007 10:55 pm 
Offline
da LUV masta
User avatar

Joined: Sat Aug 03, 2002 6:53 pm
Posts: 502
Location: Baytown ,Tx
Thanks Guys.....paint isnt an issue ,tryin to get it ready for paint.
Top
 Profile  
Reply with quote  
79-LUV'r
 Post subject: Re: Thanks
PostPosted: Sat Dec 01, 2007 11:20 pm 
Offline
Addicted to LUV
User avatar

Joined: Sat Dec 16, 2006 12:38 am
Posts: 1180
Location: Brownwood Tx
luvondope wrote:
Thanks Guys.....paint isnt an issue ,tryin to get it ready for paint.


3M makes a good adhesive remover. Friend of mine has a body shop, uses it for just what you are describing. Think he gets most of his from NAPA.

Short of that, mineral spirits should do it.

_________________
Image

FIAA: Color Guard
Top
 Profile  
Reply with quote  
litemup
 Post subject:
PostPosted: Tue Dec 04, 2007 9:25 pm 
Offline
Assimilated into LUVTruck.com
User avatar

Joined: Mon Oct 23, 2006 2:50 pm
Posts: 917
Location: Jeff City, Mo
Lacquer thinner

_________________
Too much to do and not enough time or money!
Courage is the other side of fear!
Pain is the weakness leaving the body!
Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 6 posts ] 

Board index » Technical » General Automotive

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 5 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group